How to Replace Brake Pads


ZOOM Brake Service Guide

How to Replace Brake Pads

Learn when to replace your ZOOM hydraulic brake pads and follow a step-by-step process to install new pads safely and correctly.

Brake pads are wear components. As they become thinner, braking performance can decrease and the hydraulic caliper may require greater piston travel.

For ZOOM HB-series hydraulic brakes, the official installation guide specifies a minimum brake pad thickness of 0.8 mm. If the pad reaches the replacement limit, or if it has been contaminated with oil, it should be replaced before riding.

!
Never ride with oil-contaminated brake pads.

ZOOM specifically warns that oil on the brake pad can cause brake failure. Replace contaminated pads rather than trying to return them to service.

When Should You Replace Your Brake Pads?

Brake pad wear depends on riding style, vehicle weight, terrain, speed, braking frequency, and environmental conditions. Inspect the pads regularly instead of relying only on a fixed mileage interval.

0.8 mm
ZOOM HB-Series Minimum Pad Thickness

Replace the brake pad when it reaches the specified minimum thickness or when the replacement indicator is visible.

Normal Wear

  • Pad material has become noticeably thin.
  • The pad is at or below the 0.8 mm minimum thickness.
  • The pad's replacement indicator has been reached.
  • Braking performance has decreased as the pad wears.

Replace Immediately

  • Brake pad has been contaminated with mineral oil.
  • Friction material is cracked or damaged.
  • Pad material is unevenly worn or damaged.
  • Abnormal braking noise indicates the pad may have reached its service limit.

Tools You May Need

Prepare the correct tools before removing the brake pads. The exact hardware can vary between brake configurations, so check your specific ZOOM model before beginning.

Appropriate Allen / hex wrench
Flat-blade screwdriver or pad tool
Clean lint-free cloth
Isopropyl alcohol for rotor cleaning
Protective gloves
Correct replacement ZOOM brake pads
ZOOM Tip: Keep the new brake pads away from mineral oil, grease, chain lubricant, and other contaminants. Do not touch the friction surfaces unnecessarily.

How to Replace ZOOM Brake Pads

The following procedure is based on the brake pad replacement procedure in the ZOOM HB-series installation guide.

1

Let the Brake System Cool

If the brake has recently been used heavily, allow the caliper and rotor to cool completely before beginning maintenance.

Brake components can become very hot during riding and braking. Do not touch the caliper or rotor immediately after use.

2

Remove the Wheel

Secure the vehicle and remove the wheel according to the manufacturer's wheel removal procedure.

Make sure the vehicle is stable before working on the brake caliper.

3

Remove the Old Brake Pads

Remove the retaining hardware used by your ZOOM caliper and carefully remove the worn brake pads and spring components.

Keep track of the original pad and spring orientation so the replacement components can be installed correctly.

4

Clean the Caliper and Inspect the Pistons

Clean the area around the pistons and inspect the caliper for dirt, oil leakage, or abnormal piston movement.

Before installing thicker new pads, the pistons need to be returned to their correct starting position.

5

Push the Pistons Back

Carefully press the pistons vertically back into the caliper until they reach the required starting position.

ZOOM's HB-series guide specifies pressing the pistons to their lowest position during brake pad replacement.

Important: Do not force or tilt the pistons. Avoid damaging the piston surfaces or seals while pushing them back.
6

Install the New Brake Pads

Install the new ZOOM brake pads together with the correct spring and retaining hardware for your caliper.

Make sure the friction material is facing the rotor and that the pads are seated correctly inside the caliper.

Reinstall any retaining pin or clip required by your specific brake model.

7

Reinstall the Wheel

Reinstall the wheel and make sure it is fully seated and secured according to the vehicle manufacturer's specifications.

Rotate the wheel by hand and check that the rotor is correctly positioned between the brake pads.

8

Pump the Brake Lever

Slowly squeeze and release the brake lever several times. This allows the pistons and new pads to move back into their normal working position.

Continue until the lever develops a firm and consistent feel.

9

Check Pad and Rotor Alignment

Spin the wheel and check the relationship between the rotor and the new brake pads.

There should be no continuous interference between the pads and rotor. If the rotor rubs continuously, inspect the caliper alignment and wheel installation before riding.

What If the Brake Pads Are Contaminated?

Brake pads are designed to generate friction against the rotor. Oil contamination changes the friction characteristics of the pad and can significantly reduce braking performance.

Oil on Brake Pads

Replace the brake pads. Do not continue riding with mineral-oil-contaminated friction material.

Oil on the Rotor

Thoroughly clean the rotor using an appropriate brake cleaner or isopropyl alcohol and a clean cloth. The rotor should be completely clean and dry before use.

!
Never install contaminated pads just because they still have enough material remaining.

Pad thickness alone does not determine whether a brake pad is safe to use.

Bedding In New Brake Pads

New brake pads need time to establish consistent contact with the rotor. During the initial rides, braking may feel different from the fully bedded-in system.

Start Gradually

Test the brake in a safe area at low speed first. Apply the brake progressively and allow the braking system to warm up gradually.

Avoid immediately performing repeated hard stops or riding at high speed before confirming that the new pads and brake system are operating correctly.

The exact bedding procedure can vary depending on the vehicle, rotor, pad compound, and riding conditions.

Final Safety Check

Before returning to normal riding, confirm all of the following:

New brake pads are correctly seated
Retaining hardware is correctly installed
Wheel is securely installed
Rotor is clean and dry
Brake lever feels firm
No continuous pad-to-rotor interference
No visible hydraulic oil leakage
Brake operates normally at low speed

Frequently Asked Questions

How thick should ZOOM brake pads be before replacement?

ZOOM's HB-series installation guide specifies a minimum brake pad thickness of 0.8 mm. Replace the pads when they reach the specified limit or the replacement indicator is reached.

Can I reuse brake pads contaminated with mineral oil?

No. ZOOM recommends replacing brake pads that have been contaminated with oil because contamination can cause insufficient braking performance.

Do I need to bleed the brake after replacing brake pads?

A normal pad replacement does not automatically require a full bleed. However, if the hydraulic system was opened, air entered the system, or the lever remains soft after replacement, the system should be inspected and may require bleeding.

Why does my brake rub after installing new pads?

New pads are thicker, so the piston position changes during replacement. Check that the pistons were properly reset, the wheel is correctly seated, and the caliper and rotor are aligned.

Should I replace both brake pads at the same time?

Brake pads work as a pair at the caliper. When replacing pads, use a matched new pair designed for the specific ZOOM caliper.

Need the Right Replacement Pads?

Make sure your replacement brake pads match your ZOOM brake model. If you are unsure which pad fits your caliper, contact ZOOM support with your brake model and vehicle information before ordering.

Service Note: This guide is intended for general maintenance of compatible ZOOM hydraulic disc brake systems. Brake pad shapes, retaining hardware, and installation details can vary by model. Always confirm the replacement pad is compatible with your specific ZOOM brake before installation.